Concord ,NH llc
mobile division
Features and Benefits
• Well suited for vertical applications
• Superior chemical and abrasion resistance
• Excellent bonding
• Highly resistant to cratering or blush
• Dries to a high gloss
• Low odor
• 100% solids, no solvents
• Cures in the presence of moisture and humidity with excellent mechanical properties
Applications
• Recommended for vertical applications where increased resistance to acids, bases and solvents is desired
• Great coating in areas were high concentrations of chemicals are used
• Primary and secondary containment
• Chemical tanks and disposal pits or tunnels
Application Properties (at 77°F / 25°C)
| Solids by Volume | 100% |
| VOCs (garms/liter) | 0 |
| Mixing ratio | 2:1 by volume |
| Viscosity | Thixotropic (for vertical surfaces) |
| Pot Life (neat coating) | 25-30 minutes |
| Application Temperature | 55°F minimum, 100°F maximum |
| Maximum Re-coat Time | 24 hrs. |
| Dry To Touch | 6-8 hrs. |
| Light Traffic | 14-16 hrs |
| Return To Service | 24-36-hrs. |
| Full Cure | 7 Days |
Physical Properties For Cured System (cured 7 days at 77°F (25°C)
| Hardness (Shore D) | 86+5 | |
| Tensile Strength (psi) | 7000-8000 | ASTM D-638 |
| Tensile Elongation (%) | 3.2 | ASTM D-638 |
| Flexural Strength | 13000 – 13800 | ASTM D-790 |
| Compressive Strength (psi) | 12000 – 14000 | ASTM D-695 |
| HDT (F) | 140 | ASTM D-648-264 |
| Water Absorption (% gain) 24 hrs | <1 | |
| Bond Strength (psi) to concrete | >400, w/100% concrete failure |
Mixing
A thorough and complete mixing is critical. First mix each component separately. Proportion each component at the ratio of 2 parts A (resin) to 1 part B (hardener) by volume or if using 1-gallon kits, pour all of Part B (hardener) into Part A (resin). Mix for 3 – 5 minutes, scraping the mixing container sides and bottom regularly. Mix no more material than may be applied in 20 minutes.
Tank Linings and Secondary Containment Coatings
Apply mixed product by brush or roller at the rate of 15 mils (approx. 100 sq ft per gallon). Once the first coat has tacked, but not fully cured, an additional 15 mil coating may be applied. Allow the material to cure 48 hours minimum before exposure to any chemicals (product will continue to cure for 7 days to full properties).
Chemical Resistance Guide (3 week immersion)
| Reagent | % Weight gain (loss) |
| Xylene | 0.0 |
| 1,1,1 Trichloroethane | 0.0 |
| EB (Ethylene Glycol Monobutyl Ether) | 2.4 |
| Water (deionized) | 1.2 |
| 10% Sodium Hydroxide | 0.0 |
| 10% Sulfide Acid | 0.0 |
| 10% Hydrochloric Acid | 0.1 |
| 10% Acetic Acid | 5.4 |
| Synthetic Gasohol | 0.0 |
| JP-4, JP-5, JP-7, JP-8 | 0.0 |
| Reagent | % Weight gain (loss) |
| Toluene | 2.3 |
| MEK | 2.3 |
| Ethyl Alcohol | 6.9 |
| 5% Detergent Solution | 0.0 |
| 50% Sodium Hydroxide | (0.2) |
| 70% Sulfuric Acid | 0.2 |
| 5% Acetic Acid | 2.6 |
| Skydrol | (0.03) |
| Mogas, Diesel | 0.0 |
| Diethylene Glycol Monomethyl Ether | 0.0 |
Rhino 9700: industry applications
Flooring
